Termékek pvc csík ajtók (8)

PVC Panels G 211

FE-03TK Silikon Hohlkammerdichtung transparent - Silikon Hohlkammerdichtung mit Selbstkleberücken, transparent - Fugenbreite 4 bis 6 mm - Abmessung B= 7 mm, H= 6 mm - schadstoffarm, Oddy getestet - 60 Shore A

Syntech Poliurea Top Coating A protective, pigmented, two-component formulation based on aliphatic polyurethane resins, ideal as a protective and aesthetic coating on waterproofing with SYNTECH POLIUREA SPRAY. Characterised by high levels of elasticity and elevated protection, even in aggressive atmospheres. Available on request in shades from the RAL colour range. Surface coating pigmented for colouring polyurethane claddings, and their protection from UV rays (which in the absence of the top coating would alter the colour over time). After suitable priming with SYNTECH POLYUREA PRIMER, it can also be applied as a simple coloured aliphatic protective coating. Polyurea support Vacuum and blow the surfaces to eliminate any dust that may have accumulated in the 24-48 hours following the installation of SYNTECH POLIUREA SPRAY Support in concrete, mortar, brick, tiles The support on which the polyurea system must be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to apply in advance the epoxy resin for "wet substrates" Syntech Pavidamp. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. It is recommended to use Primer from the SYNTECH POLIUREA PRIMER range. On particularly absorbent substrates, to avoid the formation of craters / blowholes on the surface of the freshly sprayed product, it is recommended to use primers from the SYNTECH POLIUREA PRIMER range, always contacting the Azichem technical staff for clarification on the most suitable type to use. Apply several layers of primer until the porosity is saturated and providing a light dusting with clean and dry quartz sand (0.4-0.7 mm). Never dust off the primer. Provide suitable elastic sealing systems to cover joints, fittings, cracks or fissures subject to significant movements. Pour component B with component A into a single container, taking care to remove all the material from the packaging. Mix thoroughly with a mixer at low revs, until a lump-free mixture is obtained. Apply with a roller or brush on the surfaces of SYNTECH POLYUREA SPRAY, within 24-48 hours of spreading the latter. A thorough sanding of the supports is recommended for any repairs and/or finishes. From 0.15 to 0.25 kg of SYNTYECH POLIUREA TOP COATING for each square metre of surface to be covered. Can 6.7 kg [A] - Can 3.3 kg [B] - Kit: 1 Can 6.7 kg [A] + 1 Can 3.3 kg [B]

COMPOSITION ET ASPECT Blanc &amp; incolore. CARACTÉRISTIQUES TECHNIQUES • Temps de formation de peau : environ 10 minutes (23°C, 50 % HR) • Temps hors poussière : environ 20 minutes (23°C, 50 % HR) • Allongement à la rupture: 150 % • ÉPAISSEUR polymérisé : en 24 h (23°C, 50 % HR) 3 mm • Température d’application : + 5°C à + 40°C CONDITIONNEMENTS Cartouche de 310 ML. STOCKAGE 18 mois à l’abri du froid et des fortes chaleurs en emballage d’origine non entamé. PRÉCAUTION D'EMPLOI Éviter le contact avec la peau. En cas de contact avec les yeux, laver immédiatement avec de l’eau et consulter un spécialiste. Conserver hors de portée des enfants. PRÉPARATION DES SUPPORTS Les supports doivent être propres, secs, sains, dégraissés et dépoussiérés. Ne pas utiliser sur support basique (maçonnerie, béton, marbre...). APPLICATION Étant donné la diversité des supports sanitaires acryliques, un essai de convenance préalable est nécessaire. Lisser à l’eau savonneuse, serrer...

VOUS SOUHAITEZ RECEVOIR UN ÉCHANTILLON GRATUIT AVANT DE RÉALISER VOTRE ACHAT ? CELA EST POSSIBLE ! FAITES VOTRE DEMANDE D'ÉCHANTILLONS GRATUITS DE SOL PVC EN SUIVANT NOS INSTRUCTIONS CI-DESSOUS. Pour tout envoi d’échantillon, merci d’indiquer dans les commentaires le type de produit que vous souhaitez recevoir, en précisant la couleur et la surface. 1 à 2 modèles par envoi. Les frais de port de 9,00 EUROS TTC seront remboursés lors de votre prochaine commande. Ajoutez au panier Renseignez toutes les informations utiles à la livraison Effectuez le paiement (9 € TTC = Frais de port uniquement) Précisez l'échantillon voulu dans la zone "Commentaire"

50.5002.00 - PVC-Kleber

We supply you with the material cellular polyethylene as blocks, sheets or rolls, further processed into strips, punched parts, molded parts or milled parts, with or without self-adhesive coating. Cellular polyethylene is one of the most versatile and modern cellular materials when it comes to application and processing quantity. That's why we produce and sell an enormous range of cross-linked PE foams in variable densities, many colors and compression hardnesses. In addition, KOPP offers you electrically conductive, static-dissipative and flame-retardant PE qualities. This program is rounded off by high-quality EVA and a unique EPDM-PE blend. The material cellular polyethylene All of our cellular polyethylene qualities combine the positive properties of a plastic: high aging resistance, high chemical resistance, low emission values, exceptionally uniform density, they are odor-free and can be thermoformed. Origin:Germany Colors:red Explanations:K/PE70

Silicone hollow chamber seal with self-adhesive spine, transparent-Oddy tested - FE-03TK silicone hollow chamber seal transparent - silicone hollow chamber seal with self-adhesive back, transparent - joint width 4 to 6 mm - dimensions W = 7 mm, H = 6 mm - emission-free and Oddy tested - 60 Shore A